Way to use boolean to fill large amounts of holes at once?

kylegonyerkylegonyer Posts: 20
edited June 10 in Carrara Discussion

So I use boolean alot to take away, but wondering how to use it to add to. In the example below I have a big box and the lower half has holes that I want to plug (yellow object to plug) Union merges, intersect takes away all but where the big box and yellow cube intersect, Box minus cube take out where yellow was including the box as expected and cube minus box for some reason is just like union. What I want to do is box minus yellow cube except where they intersect. Hope this makes sense. Holes are all the way around the bottom all side but left some and not doing so you can see. what is there

 

Post edited by kylegonyer on

Comments

  • HeadwaxHeadwax Posts: 8,783
    edited June 10

    had a brief play with a donut like cylinder and a cube

    the only way to get what you I could find  want was to to make the sure the walls of the cube were aligned exactly with or slightly below the box walls 

    before alignment 

     

     

    box in cube

    box minus cylinder

     

     

     

     

     

     

    result - interestingly you loose the box colour

     

     

    boolean.jpg
    2100 x 1353 - 527K
    boxincylinder.jpg
    2004 x 1320 - 405K
    endresult.jpg
    2105 x 1353 - 463K
    beforealignment.jpg
    2232 x 1259 - 490K
    Post edited by Headwax on
  • kylegonyerkylegonyer Posts: 20

    thanks for reply, It seems to loose the box though. I am wondering if I am going about it all wrong and if boolean is not the way to fill a hole left from a boolean. For very simple shapes with a hole I did see I could use bridge (must do on both sides of the wall or object, but with the current box and lots of holes would take alot of time. I did see some videos where users are using blender and it has a fill operation if you select the edge of the circle/s .....again not a quick plug of all the holes in two clicks thing, but does anyone know if carrara has a fill type tool, operation or modifier? or is that pretty much what bridge is?

  • HeadwaxHeadwax Posts: 8,783

    sure it's in the model room

    just make sure you select the vertex object withh the holes first

     

     

    Untitled-8.jpg
    1335 x 1043 - 366K
  • WendyLuvsCatzWendyLuvsCatz Posts: 30,608

    wouldn't it be simpler to just duplicate yellow cylinders to plug them?

  • kylegonyerkylegonyer Posts: 20
    edited June 10

    The best I was able to do is copy the objects along the same axix and only do a side at a time. That is if I want to do the long way. Just a test for now

    Which results in a union of the filled holes (minus the ends, ill get into that later) + what overlap was there for the box

    Then 2 more boolean operations needed to take box section out

    Which no matter how it is done results in no end caps for plugs, so a selection of just the edges and fill (Thanks for showing Headwax) gives me a row of exactly spaced and sized  "plugged" (but unfortunately only 1 side a time ....very tedious)
    Yes WendyLuvsCatz, this can be used to just shift back along the same axis and plug using duplication your idea got me going this route

    However, I was looking for a 2 click or very simple way to do it all with Boolean. I am not sure if Carra is capable (at least not in the assembly room)

    I think what I want to do is use some of the other 8 (of 12) but they are not accessable from the assembly room and in modeling I can only have the one object. Unless I am doing something wrong

     

    1.png
    744 x 435 - 73K
    2.png
    350 x 521 - 33K
    3.png
    915 x 457 - 17K
    4.png
    965 x 744 - 180K
    5.png
    243 x 101 - 7K
    Post edited by kylegonyer on
  • StezzaStezza Posts: 6,240

    probably quicker to just delete the section and redo with no holes.... enlightened

Sign In or Register to comment.