Loading...
> >

simulation error

dannagiusy64dannagiusy64 Posts: 477
edited December 2019 in The Commons

I did not understand why the simulation of this dress always crashes and gives me an error https://www.daz3d.com/dforce-wild-winds-outfit-for-genesis-8-females

Post edited by dannagiusy64 on

Comments

  • Richard HaseltineRichard Haseltine Posts: 109,088

    I think I have simulated that set in the past. Does this happen even if you leave the figure in the zero pose?

  • dannagiusy64dannagiusy64 Posts: 477

    I didn't try it in the zero pose. The pose I put in is still very simple. The points do not touch each other. I don't understand why it always gives me errors. I redid the file by putting back the character and clothes, with animation and without animation. It always gives me error and the simulation doesn't work

  • dannagiusy64dannagiusy64 Posts: 477

    I tried zero pose of genesis 8 and it works. But clearly I don't need this pose

  • dannagiusy64dannagiusy64 Posts: 477

    I tried and redid all over again. Nothing, keep giving me errors arrabbiato

    IMG_20191204_175129.jpg
    2336 x 4160 - 4M
  • dannagiusy64dannagiusy64 Posts: 477

    I tried without the shirt with the sleeves and the simulation works. But I want to put the shirt on triste

  • Richard HaseltineRichard Haseltine Posts: 109,088

    Are you simulating from that pose or from the zero pose? If from the zero pose are you sure that no body parts pass through each other going from zero pose to final pose? (If it's a pose from a pose set, which is it?)

  • dannagiusy64dannagiusy64 Posts: 477
    edited December 2019
    Richard Haseltine said:

    Are you simulating from that pose or from the zero pose? If from the zero pose are you sure that no body parts pass through each other going from zero pose to final pose? (If it's a pose from a pose set, which is it?)

    I don't know if I understood your question correctly. I start from the zero frame with the zero pose then at frame 60 I set the pose which is a pose I purchased. I've changed it a little, but it's not a complex pose. It arrives at about 20 frame and stops. I don't understand why this happens

    Post edited by Richard Haseltine on
  • dannagiusy64dannagiusy64 Posts: 477

    The pose I used is this package https://www.daz3d.com/teen-rebel-poses-and-expressions-for-genesis-8-female-s But I've tried so many others and re-done everything from the beginning so many times and it always stops me 

    Richard Haseltine said:

    Are you simulating from that pose or from the zero pose? If from the zero pose are you sure that no body parts pass through each other going from zero pose to final pose? (If it's a pose from a pose set, which is it?)

     

  • dannagiusy64dannagiusy64 Posts: 477

    I state that the points do not overlap during the simulation

    Richard Haseltine said:

    Are you simulating from that pose or from the zero pose? If from the zero pose are you sure that no body parts pass through each other going from zero pose to final pose? (If it's a pose from a pose set, which is it?)

     

    Richard Haseltine said:

    Are you simulating from that pose or from the zero pose? If from the zero pose are you sure that no body parts pass through each other going from zero pose to final pose? (If it's a pose from a pose set, which is it?)

     

  • eshaesha Posts: 3,261

    It does say "See log file for details."
    Have you looked at the log? What does it say there?

    And what version of DS are you using?

  • dannagiusy64dannagiusy64 Posts: 477

    the last, 4.12 

    esha said:

    It does say "See log file for details."
    Have you looked at the log? What does it say there?

    And what version of DS are you using?

     

    esha said:

    It does say "See log file for details."
    Have you looked at the log? What does it say there?

    And what version of DS are you using?

     

  • mclaughmclaugh Posts: 221
    dannagiusy64 said:

    the last, 4.12 

    esha said:

    It does say "See log file for details."
    Have you looked at the log? What does it say there?

    And what version of DS are you using?

     

    So, have you looked at the log file? 

  • TheKDTheKD Posts: 2,711

    Go to help > troubleshooting > view log file. Ctrl A backspace ctrl S, then run the sim again. It will make it easier to see what error is in log if there is one.

  • dannagiusy64dannagiusy64 Posts: 477

    ok, and what do I do with that file now? I can't read the reason for the errors 

    TheKD said:

    Go to help > troubleshooting > view log file. Ctrl A backspace ctrl S, then run the sim again. It will make it easier to see what error is in log if there is one.

     

  • Richard HaseltineRichard Haseltine Posts: 109,088

    The fulle version of the error should appear at or near the end, if you open the log just after the simulation fails.

  • dannagiusy64dannagiusy64 Posts: 477

    Yes, I have the log file. But for me it is incomprehensible.triste 

    Richard Haseltine said:

    The fulle version of the error should appear at or near the end, if you open the log just after the simulation fails.

     

  • Richard HaseltineRichard Haseltine Posts: 109,088

    Please post the error mesage relating to the failed simulation

  • dannagiusy64dannagiusy64 Posts: 477

    OK thanks. Who do I send it to? 

    Richard Haseltine said:

    Please post the error mesage relating to the failed simulation

     

  • Richard HaseltineRichard Haseltine Posts: 109,088

    Post it here.

  • dannagiusy64dannagiusy64 Posts: 477

    ecco il file

  • dannagiusy64dannagiusy64 Posts: 477

    no, he did not attach it

  • dannagiusy64dannagiusy64 Posts: 477

    Text file is not attached. Maybe it's too heavy, I don't know

  • dannagiusy64dannagiusy64 Posts: 477

    Hi, I updated the nvidia card and the error it gave me seems to be solved. But this dress still does not work well. After a few frames explodes, his fingers get caught in the sleeves of his shirt, is there a way to circumvent the obstacle?

  • felisfelis Posts: 6,070

    Explosions usually happens if cloth get trapped.

    Such as if a body part moves through the torso.

    What I normally do is using timeline for simulation, and then you can correct such things with an in-between pose, so there is no intersecting.

Sign In or Register to comment.